我的开发板(tiny6410)LCD屏上
starting qtopia,please waiting...
后就进不去了，，
内核是自己移植的，，QT用的是友善自己的，
怎么回事呢2？
串口显示如下：
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.38 (
root@localhost.localdomain) (gcc version 4.5.1 (ctng-1.8.1
-FA) ) #24 Fri Sep 23 16:48:21 CST 2011
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: MINI6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
camera: no parent clock specified
S3C64XX: PLL settings, A=533000000, M=533000000, E=24000000
S3C64XX: HCLK2=266500000, HCLK=133250000, PCLK=66625000
mout_apll: source is fout_apll (1), rate is 533000000
mout_epll: source is epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 533000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-bus-host: source is clk_48m (0), rate is 48000000
uclk1: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
camera: no parent clock specified
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: init=/linuxrc rootfstype=ubifs root=ubi0:FriendlyARM-root u
bi.mtd=2 console=ttySAC0,115200
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126500k/126500k available, 4572k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff600000 - 0xffe00000 ( 8 MB)
vmalloc : 0xc8800000 - 0xf6000000 ( 728 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0023000 ( 108 kB)
.text : 0xc0023000 - 0xc02f89b8 (2903 kB)
.data : 0xc02fa000 - 0xc031f580 ( 150 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:246
VIC @f6000000: id 0x00041192, vendor 0x41
VIC @f6010000: id 0x00041192, vendor 0x41
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... 532.48 BogoMIPS (lpj=2662400)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
MINI6410: Option string mini6410=0
MINI6410: selected LCD display is 480x272
this is platdata
s3c64xx_dma_init: Registering DMA channels
PL080: IRQ 73, at c8808000, channels 0..8
PL080: IRQ 74, at c880c000, channels 8..16
S3C6410: Initialising architecture
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
squashfs: version 4.0 (2009/01/31) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
S3C_LCD clock got enabled :: 133.250 Mhz
LCD TYPE :: A70 will be initialized
Window[0] - FB1: map_video_memory: clear ff600000:00177000
FB1: map_video_memory: dma=57a00000 cpu=ff600000 size=00177000
Window[0] - FB2: map_video_memory: clear ff6bb800:000bb800
FB2: map_video_memory: dma=57abb800 cpu=ff6bb800 size=000bb800
Console: switching to colour frame buffer device 100x30
fb0: s3cfb frame buffer device
Window[1] - FB1: map_video_memory: clear ff800000:00177000
FB1: map_video_memory: dma=57000000 cpu=ff800000 size=00177000
Window[1] - FB2: map_video_memory: clear ff8bb800:000bb800
FB2: map_video_memory: dma=570bb800 cpu=ff8bb800 size=000bb800
fb1: s3cfb frame buffer device
Window[2] - FB1: map_video_memory: clear ffa00000:000bb800
FB1: map_video_memory: dma=57900000 cpu=ffa00000 size=000bb800
fb2: s3cfb frame buffer device
Window[3] - FB1: map_video_memory: clear ffb00000:000bb800
FB1: map_video_memory: dma=57200000 cpu=ffb00000 size=000bb800
fb3: s3cfb frame buffer device
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s3c6400-uart.0: ttySAC0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: ttySAC1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: ttySAC2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: ttySAC3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
loop: module loaded
S3C NAND Driver, (c) 2008 Samsung Electronics
MLC nand initialized, 2011 ported by FriendlyARM
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 2GiB 3,3V 8-bit":
0x000000000000-0x000000400000 : "Bootloader"
0x000000400000-0x000000c00000 : "Kernel"
0x000000c00000-0x000080000000 : "File System"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 1048576 bytes (1024 KiB)
UBI: logical eraseblock size: 1032192 bytes
UBI: smallest flash I/O unit: 8192
UBI: VID header offset: 8192 (aligned 8192)
UBI: data offset: 16384
UBI: max. sequence number: 8
UBI: attached mtd2 to ubi0
UBI: MTD device name: "File System"
UBI: MTD device size: 2036 MiB
UBI: number of good PEBs: 2027
UBI: number of bad PEBs: 9
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 2027
UBI: number of PEBs reserved for bad PEB handling: 20
UBI: max/mean erase counter: 2/0
UBI: image sequence number: 1021995190
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
UBI: background thread "ubi_bgt0d" started, PID 865
s3c2410-ohci s3c2410-ohci: init err (00000000 0000)
ohci_hcd: can't start s3c24xx
s3c2410-ohci s3c2410-ohci: startup error -75
s3c2410-ohci s3c2410-ohci: USB bus 1 deregistered
s3c2410-ohci: probe of s3c2410-ohci failed with error -75
mousedev: PS/2 mouse device common for all mice
S3C Touchscreen driver, (c) 2010 FriendlyARM
touchscreen got loaded successfully : 12 bits
touchscreen-1wire initialized
backlight-1wire initialized
input: TouchScreen Pipe as /devices/virtual/input/input0
ts-if initialized
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
i2c /dev entries driver
Linux video capture interface: v2.00
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133250000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133250000 Hz)
one_wire_status: 4
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133250000 Hz)
one_wire_status: 4
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133250000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
mmc0: mmc_rescan_try_freq: trying to init card at 300000 Hz
UBIFS: recovery needed
mmc0: mmc_rescan_try_freq: trying to init card at 200000 Hz
mmc0: mmc_rescan_try_freq: trying to init card at 100000 Hz
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "FriendlyARM-root"
UBIFS: file system size: 2057158656 bytes (2008944 KiB, 1961 MiB, 1993 LEBs)
UBIFS: journal size: 12517376 bytes (12224 KiB, 11 MiB, 13 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
one_wire_status: 2
VFS: Mounted root (ubifs filesystem) on device 0:10.
Freeing init memory: 108K
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 300000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 200000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 100000 Hz
hwclock: can't open '/dev/misc/rtc': No such file or directory
[01/Jan/1970:00:00:20 +0000] boa.c:173 - unable to create socket: Address family
not supported by protocol
open device leds: No such file or directory
/usr/sbin/alsactl: load_state:1610: No soundcards found...
ifconfig: socket: Address family not supported by protocol
Try to bring eth0 interface up......cat: can't open '/sys/class/net/eth0/address
': No such file or directory
ifconfig: socket: Address family not supported by protocol
route: socket: Address family not supported by protocol
Done
Please press Enter to activate this console.
[root@FriendlyARM /]#
