如题，安卓5.1，启动过程中可以看到信息输出，但启动后就无法输入输出信息，求大神指导
[ 5.904000] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[ 5.912000] android_usb: already disabled
[ 5.924000] adb_open
[ 5.924000] mtp_bind_config
[ 5.924000] adb_bind_config
[ 6.028000] USB RESET
[ 6.096000] WARN::ep0_do_stall:1336: req 00.10 protocol STALL; err -22
[ 6.096000]
[ 6.100000] android_work: sent uevent USB_STATE=CONNECTED
[ 6.260000] logd.auditd: start
shell@nanopi3:/ $ [ 6.604000] USB RESET
[ 6.676000] USB RESET
[ 6.840000] healthd: No charger supplies found
[ 6.840000] healthd: No battery devices found
[ 6.852000] android_usb gadget: high-speed config #1: android
[ 6.852000] android_work: sent uevent USB_STATE=CONFIGURED
[ 7.080000] ov5640_link_setup
[ 7.080000] camera_common_vin_setup_io
[ 7.080000] i2c-nxp.0: ack was not received
[ 7.084000] i2c->nxp.0: incomplete xfer (-6)
[ 7.092000] ov5640 0-003c: reg_write: i2c write error, reg: 3103
[ 7.096000] ov5640_init: failed to ov5640_write_array init regs
[ 7.104000] ov5640_s_power.............1944...........
[ 7.108000] nxp_hdmi_link_setup: connected to me!!!
[ 11.356000] warning: `main' uses 32-bit capabilities (legacy support in use)
[ 17.636000] healthd: battery none chg=
[ 18.224000] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[ 18.228000] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[ 18.232000] lowmemorykiller: oom_adj 1 => oom_score_adj 58
[ 18.236000] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[ 18.244000] lowmemorykiller: oom_adj 3 => oom_score_adj 176
[ 18.248000] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[ 18.252000] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[ 18.260000] nxp_mlc_set_crop: pad(0), crop(0,0,1920,1080)
[ 18.264000] nxp_mlc_s_stream: enable 1, client VIDEO MLC RGB1, is_video 0
[ 18.272000] _hw_configure_rgb 1: code(0x86530000), w(1920), h(1080), pixelbyte(4)
[ 18.280000] _hw_configure_rgb 1 crop(0:0:1920:1080)
[ 18.284000] _hw_rgb_enable: module 1, enable 1
[ 18.288000] Fail, SYNCGEN1 not set sync ...
[ 18.292000] nxp_hdmi_s_stream: enable 1
[ 18.296000] hdmi_run entered
[ 18.308000] HDMI PHY Ready!!!
[ 18.308000] _set_hdmi_mux: entered: me e5340c00, remote e534080c
[ 18.312000] source device : SYNCGEN1
[ 18.316000] _set_hdmi_mux: exit
[ 18.320000] Display.1 fps=80 (12 ms), wait= 5 jiffies, Pixelclk=200000000hz
[ 18.328000] _calc_hdmi_sync_param: _h_sync_offset 0
[ 18.360000] hdmi_run exit
[ 19.076000] acc_open
[ 19.076000] acc_release
[ 19.240000] eth0: device MAC address 92:55:6a:f5:b8:31
[ 19.332000] HDMI HPD State 0x1
[ 20.784000] mtp_open
