你好 都是按照楼主帖子做的,区别我的编译器用的友善提供的4.5.1,还有就是nfs 挂载我用的环境变量#set bootargs root=/dev/nfs console=ttySAC0,115200 nfsroot=192.168.0.21:/opt/210/qtopia ip=192.168.0.122:192.168.0.21:192.168.0.2:255.255.255.0::eth0:off
内核用的是光盘里linux-3.0.8-20121030.tgz,配置文件也是用的楼主的,但是我从sd卡启动
U-Boot 2013.01-rc2 (Jan 10 2013 - 11:00:16) for FriendlyLEG-TINY210
CPU: S5PC110@1000MHz
Board: FriendlyLEG-TINY210
DRAM: 512 MiB
WARNING: Caches not enabled
PWM Moudle Initialized.
GPD0CON : 1111, GPD0DAT : e
NAND: 2048 MiB
MMC: SAMSUNG SD/MMC: 0, SAMSUNG SD/MMC: 1
In: serial
Out: serial
Err: serial
Net: dm9000
Hit any key to stop autoboot: 0
dm9000 i/o: 0x88001000, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
operating at 100M full duplex mode
Using dm9000 device
TFTP from server 192.168.0.179; our IP address is 192.168.0.122
Filename 'uImage'.
Load address: 0x21000000
Loading: #################################################################
#################################################################
#################################################################
#################################################
done
Bytes transferred = 3579564 (369eac hex)
## Booting kernel from Legacy Image at 21000000 ...
Image Name: Linux-3.0.8-TINY210V2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3579500 Bytes = 3.4 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.8-TINY210V2 (root@desktop) (gcc version 4.5.1 (ctng-1.8.1-FA) ) #2 PREEMPT Thu Jan 24 11:23:47 AFT 2013
[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: MINI210
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110220)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
[ 0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
[ 0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
[ 0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_onenand: source is hclk_dsys (1), rate is 166750000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] sclk_mixer: source is sclk_dac (0), rate is 54000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[ 0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_g3d: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3dbf5000, 0-bank base(0x3dbf5000)
[ 0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3b7f5000, 1-bank base(0x00000000)
[ 0.000000] s5p: 6144 kbytes system memory reserved for fimc0 at 0x3b1f5000, 1-bank base(0x00000000)
[ 0.000000] s5p: 16 kbytes system memory reserved for fimc1 at 0x3b1f1000, 1-bank base(0x00000000)
[ 0.000000] s5p: 6144 kbytes system memory reserved for fimc2 at 0x3abf1000, 1-bank base(0x00000000)
[ 0.000000] s5p: 8192 kbytes system memory reserved for jpeg at 0x3a3f1000, 0-bank base(0x3a3f1000)
[ 0.000000] s5p: 13060 kbytes system memory reserved for fimd at 0x39730000, 1-bank base(0x00000000)
[ 0.000000] s5p: 8192 kbytes system memory reserved for g2d at 0x38f30000, 0-bank base(0x38f30000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 101179
[ 0.000000] Kernel command line: root=/dev/nfs console=ttySAC0,115200 nfsroot=192.168.0.21:/opt/210/qtopia ip=192.168.0.122:192.168.0.21:192.168.0.2:255.255.255.0::eth0:off
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 399MB 0MB = 399MB total
[ 0.000000] Memory: 396848k/512324k available, 11964k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfd000000 ( 456 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)
[ 0.000000] .text : 0xc002d000 - 0xc06a6cf4 (6632 kB)
[ 0.000000] .data : 0xc06a8000 - 0xc06efc80 ( 288 kB)
[ 0.000000] .bss : 0xc06efca4 - 0xc0734040 ( 273 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:393
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2937815369]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.440490] Calibrating delay loop... 994.84 BogoMIPS (lpj=1941504)
[ 0.464784] pid_max: default: 32768 minimum: 301
[ 0.465027] Mount-cache hash table entries: 512
[ 0.465524] Initializing cgroup subsys debug
[ 0.465577] Initializing cgroup subsys cpuacct
[ 0.465633] Initializing cgroup subsys freezer
[ 0.468970] CPU: Testing write buffer coherency: ok
[ 0.479404] print_constraints: dummy:
[ 0.479697] NET: Registered protocol family 16
[ 0.498148] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.514791] fimd at 0x39730000
[ 0.514903] hsmmc0: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.514974] hsmmc1: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.515037] hsmmc2: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.515097] hsmmc3: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.522730] S5PV210: Initializing architecture
[ 0.527397] s3c-adc s5pv210-adc: attached adc driver
[ 0.530357] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[ 0.539653] print_constraints: pd_tv_supply: 5000 mV normal
[ 0.544534] print_constraints: pd_lcd_supply: 5000 mV normal
[ 0.550246] print_constraints: pd_g3d_supply: 5000 mV normal
[ 0.555964] print_constraints: pd_mfc_supply: 5000 mV normal
[ 0.561694] print_constraints: pd_audio_supply: 5000 mV normal
[ 0.630398] bio: create slab <bio-0> at 0
[ 0.633102] SCSI subsystem initialized
[ 0.638469] usbcore: registered new interface driver usbfs
[ 0.639287] usbcore: registered new interface driver hub
[ 0.639815] usbcore: registered new device driver usb
[ 0.641554] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.641614] s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz
[ 0.644723] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.648571] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.653382] s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
[ 0.659939] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.664695] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.669588] s3c-i2c s3c2440-i2c.2: bus frequency set to 378 KHz
[ 0.676630] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.682570] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.688475] Bluetooth: Core ver 2.16
[ 0.691025] NET: Registered protocol family 31
[ 0.695210] Bluetooth: HCI device and connection manager initialized
[ 0.701484] Bluetooth: HCI socket layer initialized
[ 0.706290] Bluetooth: L2CAP socket layer initialized
[ 0.711352] Bluetooth: SCO socket layer initialized
[ 0.717300] cfg80211: Calling CRDA to update world regulatory domain
[ 0.724051] Switching to clocksource clock_source_systimer
[ 0.730420] Switched to NOHz mode on CPU #0
[ 0.766424] NET: Registered protocol family 2
[ 0.766691] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.767644] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.767961] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.769523] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.775868] TCP reno registered
[ 0.778904] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.784792] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.791394] NET: Registered protocol family 1
[ 0.795881] RPC: Registered named UNIX socket transport module.
[ 0.801357] RPC: Registered udp transport module.
[ 0.805991] RPC: Registered tcp transport module.
[ 0.810661] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.817293] PMU: registered new PMU device of type 0
[ 0.822719] cpuidle: phy_regs_save:0x389ff000
[ 0.826671] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 0.831353] DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[ 0.837577] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 0.842314] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.848501] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 0.853318] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.868585] ashmem: initialized
[ 0.901322] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.902018] msgmni has been set to 775
[ 0.904919] io scheduler noop registered
[ 0.904966] io scheduler deadline registered
[ 0.905212] io scheduler cfq registered (default)
[ 0.905258] start plist test
[ 0.908612] end plist test
[ 0.909327] s3cfb s3cfb: win 2: pmem_start=0x39b95000
[ 0.910444] s3cfb s3cfb: [fb2] dma: 0x39b95000, cpu: 0xe1000000, size: 0x0085c000
[ 0.927600] FIMD src sclk = 166750000
[ 0.927711] s3cfb s3cfb: registered successfully
[ 0.946734] s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 0.954843] s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 0.962651] s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 0.970440] s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 0.979599] leds initialized
[ 0.980118] pwm initialized
[ 0.980684] mini210-adc initialized
[ 0.981597] backlight initialized
[ 0.983718] PA FB = 0x39B95000, bits per pixel = 32
[ 0.983770] screen width=800 height=480 va=0xd9b95000 pa=0x39b95000
[ 0.983825] xres_virtual = 800, yres_virtual = 1440, xoffset = 0, yoffset = 0
[ 0.988161] fb_size=8765440
[ 0.990802] Back frameBuffer[0].VAddr=d9d0c000 PAddr=39d0c000 size=1536000
[ 0.997635] Back frameBuffer[1].VAddr=d9e83000 PAddr=39e83000 size=1536000
[ 1.004452] Video Y Buffer[0].VAddr=d9ffa000 PAddr=39ffa000 size=921600
[ 1.011020] Video Y Buffer[1].VAddr=da0db000 PAddr=3a0db000 size=921600
[ 1.017603] Video Y Buffer[2].VAddr=da1bc000 PAddr=3a1bc000 size=921600
[ 1.024178] Video UV Buffer[0].VAddr=da29d000 PAddr=3a29d000 size=462848
[ 1.030858] Video UV Buffer[1].VAddr=da30e000 PAddr=3a30e000 size=462848
[ 1.037533] Video UV Buffer[2].VAddr=da37f000 PAddr=3a37f000 size=462848
[ 1.061157] brd: module loaded
[ 1.070016] loop: module loaded
[ 1.073342] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.177049] MLC nand init failed, -19, 2012 ported by FriendlyARM
http://www.arm9.net[ 1.177126] S3C NAND Driver is using hardware ECC.
[ 1.177206] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit)
[ 1.177324] No oob scheme defined for oobsize 512
[ 240.864812] INFO: task kinteractiveup:436 blocked for more than 120 seconds.
[ 240.864888] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.864956] kinteractiveup D c04b5dc8 0 436 2 0x00000000
换了几张卡 步骤也是跟楼主一样,可是还是不能启动,tiny210 v2 板子烧友善光盘里面的image 从nand 启动都是正常的!