我开始装的是虚拟机的fedora 11，然后又装了个真实的fedora 11
fedora 11 先是找不到ip设置，
好吧 我就用
ifconfig eth0 192.168.1.111 broadcast 192.168.1.111(这里有点怪，根据下面设的) netmask 255.255.255.0
是根据手册上的：
第一项(192.168.1.70)是目标板的临时IP(注意不要和局域网内其他IP 冲突)；
第二项(192.168.1.111)是开发主机的IP；
第三项(192.168.1.111)是目标板上网关(GW)的设置；
第四项(255.255.255.0)是子网掩码；
第五项是开发主机的名字(一般无关紧要，可随便填写)
设置的。。。。。。
nfs的设置
我的nfs文件夹是 /root/a/root_qtopia
1.修改 /etc/exports 加上
/root/a/root_qtopia *(rw,sync,no_root_squash)
2.起动：#/etc/init.d/nfs start（没有什么异常）
参数是：
param set linux_cmd_line "console=ttySAC0 root=/dev/nfs nfsroot=192.168.1.111:/root/a/root_qtopia ip=192.168.1.70:192.168.1.111:192.168.1.111:255.255.255.0:sbc2440.arm9.net:eth0:off"
然后 boot
防火墙 关了。。。。
电脑的网卡 好像 一直 不通样的
以下 是串口 打印的：
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 505 at 0x000003f20000
Creating 4 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x000000000000-0x000000060000 : "supervivi"
0x000000060000-0x000000260000 : "Kernel"
0x000000260000-0x000040260000 : "root"
mtd: partition "root" extends beyond the end of device "NAND 128MiB 3,3V 8-bit"
-- size truncated to 0x7da0000
0x000000000000-0x000040000000 : "nand"
mtd: partition "nand" extends beyond the end of device "NAND 128MiB 3,3V 8-bit"
-- size truncated to 0x8000000
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.29.4-FriendlyARM ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mice: PS/2 mouse device common for all mice
s3c2410 TouchScreen successfully loaded
input: s3c2410 TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz).
s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz).
s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz).
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
#0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2009-12-15 12:10:50 UTC (126087
9050)
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.1.70, mask=255.255.255.0, gw=192.168.1.111,
host=sbc2440, domain=, nis-domain=arm9.net,
bootserver=192.168.1.111, rootserver=192.168.1.111, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.111
eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
eth0: link down
eth0: link up, 10Mbps, full-duplex, lpa 0x4C61
rpcbind: server 192.168.1.111 not responding, timed out
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.1.111
