主题 : andorid在MINI6410上的启动 复制链接 | 浏览器收藏 | 打印
级别: 侠客
UID: 3653
精华: 0
发帖: 57
金钱: 325 两
威望: 129 点
贡献值: 0 点
综合积分: 114 分
注册时间: 2009-01-31
最后登录: 2015-01-25
楼主  发表于: 2010-08-02 13:49

 andorid在MINI6410上的启动

管理提醒: 本帖被 arm9home 从 Android技术交流专区 移动到本区(2010-09-09)
请问大侠霍版主,我按照手册上的要求烧写andorid,不知道第一次初始化一般要等多久啊???下面是串口输出的部分信息,对吗??在线等哦~~~

init: cannot open '/initlogo.rle'
init: cannot find '/system/bin/playmp3', disabling 'bootsound'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
sh: can't access tty; job control turned off
# warning: `rild' uses 32-bit capabilities (legacy support in use)
request_suspend_state: wakeup (3->0) at 117300894376 (2000-08-02 13:35:12.086419
294 UTC)
级别: 侠客
UID: 3653
精华: 0
发帖: 57
金钱: 325 两
威望: 129 点
贡献值: 0 点
综合积分: 114 分
注册时间: 2009-01-31
最后登录: 2015-01-25
1楼  发表于: 2010-08-02 14:55
Load Kernel...
Load Kernel succeed
Uncompressing Linux.............................................................
...............................................................................
done, booting the kernel.
Linux version 2.6.28.6 (root@russell-work-pc) (gcc version 4.4.3 (ctng-1.6.1) )
#2 Sat Jul 24 19:16:06 CST 2010
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266000000, HCLK=133000000, PCLK=66500000
div1: 00000555
mout_apll: source is fout_apll (1), rate is 532000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi_epll: source is mout_epll (0), rate is 24000000
spi_epll: source is mout_epll (0), rate is 24000000
sclk_audio0: source is mout_epll (0), rate is 24000000
sclk_audio1: source is mout_epll (0), rate is 24000000
sclk_audio2: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: init=/linuxrc rootfstype=ubifs root=ubi0:FriendlyARM-root u
bi.mtd=2 console=ttySAC0,115200
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 124756KB available (3304K code, 771K data, 900K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 530.84 BogoMIPS (lpj=1327104)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
S3C6410 Power Management, (c) 2008 Samsung Electronics
S3C6410: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
yaffs Jul 24 2010 19:09:33 Installing.
msgmni has been set to 243
alg: No test for stdrng (krng)
io scheduler noop registered (default)
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: LTE480WV will be initialized
Window[0] - FB1: map_video_memory: clear ff000000:003a9800
            FB1: map_video_memory: dma=57400000 cpu=ff000000 size=003a9800
Console: switching to colour frame buffer device 100x30
fb0: s3cfb frame buffer device
backlight       initialized
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
loop: module loaded
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
dm9000 Ethernet Driver
dm9000: read wrong id 0x2b2a2928
dm9000: read wrong id 0x2b2a2928
dm9000: wrong id: 0x2b2a2928
dm9000: not found (-19).
console [netcon0] enabled
netconsole: network logging started
Linux video capture interface: v2.00
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bi
t)
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x00000000-0x00080000 : "Bootloader"
0x00080000-0x00580000 : "Kernel"
0x00580000-0x10000000 : "File System"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: volume 0 ("FriendlyARM-root") re-sized from 332 to 1980 LEBs
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "File System"
UBI: MTD device size:            250 MiB
UBI: number of good PEBs:        2004
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 2004
UBI: number of PEBs reserved for bad PEB handling: 20
UBI: max/mean erase counter: 1/0
UBI: background thread "ubi_bgt0d" started, PID 359
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android init
mice: PS/2 mouse device common for all mice
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
pointercal      initialized
S3C Touchscreen driver, (c) 2008 Samsung Electronics
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /devices/virtual/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410_rtc: tick irq 34, alarm irq 92
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44333333 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
ASoC version 0.13.2
smdk6400_init:67
WM9713/WM9714 SoC Audio Codec 0.15
playback: 1, capture : 1
asoc: AC97 HiFi <-> s3c64xx-ac97 mapping ok
mmc0: new high speed SD card at address 1234
mmcblk0: mmc0:1234 SD1GB 972 MiB
mmcblk0: p1
AC97 link error
soc-audio: probe of soc-audio failed with error -5
ALSA device list:
  No soundcards found.
TCP cubic registered
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
s3c2410-rtc s3c2410-rtc: setting system clock to 2000-08-02 14:34:47 UTC (965226
887)
Freeing init memory: 900K
UBIFS: mounted UBI device 0, volume 0, name "FriendlyARM-root"
UBIFS: file system size:   254048256 bytes (248094 KiB, 242 MiB, 1969 LEBs)
UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format:       4 (latest is 4)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  0 bytes (0 KiB)
xres = 800, yres = 480
Took 110 samples...
Top left : X = 1307 Y = 3116
Took 120 samples...
Top right : X = 1263 Y = 1014
Took 4 samples...
Bot right : X = 2617 Y = 1079
Took 53 samples...
Bot left : X = 2620 Y = 1016
Took 106 samples...
Center : X = 1960 Y = 2073
1316.611328 -0.222566 -0.290338
-298.576172 0.280587 -0.005735
pointercal_ioctl: -14586 -19027 86285440 18388 -375 -19567488 65536
init: cannot open '/initlogo.rle'
init: cannot find '/system/bin/playmp3', disabling 'bootsound'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
sh: can't access tty; job control turned off
# warning: `rild' uses 32-bit capabilities (legacy support in use)
request_suspend_state: wakeup (3->0) at 116808114767 (2000-08-02 14:36:38.598800
423 UTC)
*無鈳取玳
级别: 论坛版主
UID: 27
精华: 12
发帖: 5398
金钱: 40120 两
威望: 17929 点
贡献值: 71 点
综合积分: 11036 分
注册时间: 2008-01-16
最后登录: 2014-11-22
2楼  发表于: 2010-08-02 15:31
如果你现在还没有看到Android的Home Screen的话,在#提示符后面(如果没看见的话,在串口终端上敲几个回车)打“logcat”看看
"If you have an apple and I have an apple and we exchange apples, then you and I will
still each have one apple. But if you have an idea and I have an idea and we exchange
these ideas, then each of us will have two ideas."
级别: 侠客
UID: 3653
精华: 0
发帖: 57
金钱: 325 两
威望: 129 点
贡献值: 0 点
综合积分: 114 分
注册时间: 2009-01-31
最后登录: 2015-01-25
3楼  发表于: 2010-08-02 17:16
那请问版主打“logcat”看韶??初学者,呵呵~~~
*無鈳取玳
级别: 论坛版主
UID: 27
精华: 12
发帖: 5398
金钱: 40120 两
威望: 17929 点
贡献值: 71 点
综合积分: 11036 分
注册时间: 2008-01-16
最后登录: 2014-11-22
4楼  发表于: 2010-08-02 19:01
看你看到的东西
"If you have an apple and I have an apple and we exchange apples, then you and I will
still each have one apple. But if you have an idea and I have an idea and we exchange
these ideas, then each of us will have two ideas."
级别: 侠客
UID: 3653
精华: 0
发帖: 57
金钱: 325 两
威望: 129 点
贡献值: 0 点
综合积分: 114 分
注册时间: 2009-01-31
最后登录: 2015-01-25
5楼  发表于: 2010-08-02 23:34
最后没有按版主那样做,我把飞灵的OK6410的文件拿来烧写,成功了(因为硬件上事先对比过)。发现OK6410烧写完成后,第一次进入桌面也很快,但感觉MINI6410跑ANDORID依然不太流畅,估计对系统优化下会好点,不错,还是跑起了嘛,后续可以学习了