我想在我的开发板上启动ubuntu13.10，咱们5月发布的那个，我按照nanopc的文档做了一个8G的卡，但是放到开发板（板子号1306）上没有图形界面。具体log如下：
喧K
U-Boot 2010.12-00016-g703abcf (Mar 06 2014 - 17:17:27) for TINY4412
CPU: S5PC220 [Samsung SOC on SMP Platform Base on ARM CortexA9]
APLL = 1500MHz, MPLL = 800MHz
Board: TINY4412
DRAM: 1023 MiB
vdd_arm: 1.2
vdd_int: 1.1
vdd_mif: 1.1
TrustZone Enabled BSP
BL1 version: 20120711
Checking Boot Mode ... SDMMC
REVISION: 1.1
MMC Device 0: 7580 MB
NAME: S5P_MSHC4
MMC Device 1: 3728 MB
MMC Device 2: N/A
Net: No ethernet found.
Checking K1 for system update....Skipped.
Hit any key to stop autoboot: 0
Partition1: Start Address(0x19000), Size(0x19000)
reading zImage
4059128 bytes read
Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0xa00
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.8.13.16 (fa@fa) (gcc version 4.7.3 20130102 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.01-20130125 - Linaro GCC 2013.01) ) #1 SMP PREEMPT Thu May 22 16:59:11 CST 2014 ()
[ 0.000000] Kernel was built at commit id ''
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: NANOPC_T1
[ 0.000000] TINY4412: S70 selected
[ 0.000000] cma: CMA: reserved 64 MiB at 43000000
[ 0.000000] cma: CMA: reserved 64 MiB at 51000000
[ 0.000000] cma: CMA: reserved 128 MiB at 67800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS4412 (id 0xe4412011)
[ 0.000000] exynos4_init_clocks: initializing clocks
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s3c_register_clksrc: clock armclk has no registers set
[ 0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[ 0.000000] audiocdclk: no parent clock specified
[ 0.000000] exynos4_setup_clocks: registering clocks
[ 0.000000] exynos4_setup_clocks: xtal is 24000000
[ 0.000000] EXYNOS4: PLL settings, A=1500000000, M=800000000, E=96000000 V=350000000
[ 0.000000] EXYNOS4: ARMCLK=1500000000, DMC=400000000, ACLK200=160000000
[ 0.000000] ACLK100=100000000, ACLK160=160000000, ACLK133=133333333
[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam0: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam1: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimd: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 50000000
[ 0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 50000000
[ 0.000000] On node 0 totalpages: 261888
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 193040 pages, LIFO batch:31
[ 0.000000] HighMem zone: 526 pages used for memmap
[ 0.000000] HighMem zone: 66802 pages, LIFO batch:15
[ 0.000000] Running under secure firmware.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1255000 s7936 r8192 d12544 u32768
[ 0.000000] pcpu-alloc: s7936 r8192 d12544 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259842
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootfstype=ext4 console=ttySAC0,115200n8 lcd=S70 skipcali=y ctp=2 video=HDMI-A-1:1920x1080@60 drm_kms_helper.edid_firmware=edid/1920x1080.bin
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 1023MB = 1023MB total
[ 0.000000] Memory: 765156k/765156k available, 282396k reserved, 269312K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05ecf90 (6036 kB)
[ 0.000000] .init : 0xc05ed000 - 0xc09a6f00 (3816 kB)
[ 0.000000] .data : 0xc09a8000 - 0xc0a0b660 ( 398 kB)
[ 0.000000] .bss : 0xc0a0b660 - 0xc0a48050 ( 243 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:549
[ 0.000000] MCT clocksource init timer with clk_rate=24000000 hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000164] Calibrating delay loop... 2991.71 BogoMIPS (lpj=7479296)
[ 0.045022] pid_max: default: 32768 minimum: 301
[ 0.045226] Mount-cache hash table entries: 512
[ 0.046004] Initializing cgroup subsys cpuacct
[ 0.046020] Initializing cgroup subsys devices
[ 0.046061] CPU: Testing write buffer coherency: ok
[ 0.046330] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[ 0.046435] Setting up static identity map for 0x4045ed48 - 0x4045eda0
[ 0.046480] L310 cache controller enabled
[ 0.046492] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x7e470001, Cache size: 1048576 B
[ 0.096619] CPU1: Booted secondary processor
[ 0.116360] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[ 0.126608] CPU2: Booted secondary processor
[ 0.146360] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[ 0.156622] CPU3: Booted secondary processor
[ 0.176360] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[ 0.176383] Brought up 4 CPUs
[ 0.176398] SMP: Total of 4 processors activated (11966.87 BogoMIPS).
[ 0.176979] devtmpfs: initialized
[ 0.181227] regulator-dummy: no parameters
[ 0.186260] NET: Registered protocol family 16
[ 0.197849] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.202479] s5p_hdmi_cec_set_platdata()
[ 0.205558] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.205564] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.205624] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.205686] EXYNOS4x12 PMU Initialize
[ 0.207045] EXYNOS: Initializing architecture
[ 0.207596] s3c24xx-pwm s3c24xx-pwm.1: tin at 100000000, tdiv at 100000000, tin=divclk, base 8
[ 0.217985] bio: create slab <bio-0> at 0
[ 0.218373] hdmi_5v: 5000 mV
[ 0.219362] usbcore: registered new interface driver usbfs
[ 0.219437] usbcore: registered new interface driver hub
[ 0.219534] usbcore: registered new device driver usb
[ 0.219895] i2c-gpio i2c-gpio.2: using pins 6 (SDA) and 7 (SCL)
[ 0.220002] i2c-gpio i2c-gpio.4: using pins 200 (SDA) and 199 (SCL)
[ 0.220113] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.220122] s3c-i2c s3c2440-i2c.0: bus frequency set to 195 KHz
[ 0.220314] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.220347] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.220356] s3c-i2c s3c2440-i2c.1: bus frequency set to 390 KHz
[ 0.220457] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.220501] s3c-i2c s3c2440-i2c.3: slave address 0x10
[ 0.220510] s3c-i2c s3c2440-i2c.3: bus frequency set to 390 KHz
[ 0.220625] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 0.220660] s3c-i2c s3c2440-i2c.7: slave address 0x10
[ 0.220669] s3c-i2c s3c2440-i2c.7: bus frequency set to 390 KHz
[ 0.220858] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 0.220898] s3c-i2c s3c2440-hdmiphy-i2c: slave address 0x10
[ 0.220906] s3c-i2c s3c2440-hdmiphy-i2c: bus frequency set to 390 KHz
[ 0.221107] s3c-i2c s3c2440-hdmiphy-i2c: i2c-8: S3C I2C adapter
[ 0.221186] media: Linux media interface: v0.10
[ 0.221255] Linux video capture interface: v2.00
[ 0.221827] Advanced Linux Sound Architecture Driver Initialized.
[ 0.222485] cfg80211: Calling CRDA to update world regulatory domain
[ 0.222921] Switching to clocksource mct-frc
[ 0.232167] NET: Registered protocol family 2
[ 0.232511] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.232596] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 0.232781] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.232926] TCP: reno registered
[ 0.232936] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 0.232996] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 0.233157] NET: Registered protocol family 1
[ 0.248102] CPU PMU: probing PMU on CPU 2
[ 0.248120] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.249350] bounce pool size: 64 pages
[ 0.255871] msgmni has been set to 1480
[ 0.256453] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.256460] io scheduler noop registered
[ 0.256465] io scheduler deadline registered
[ 0.256589] io scheduler cfq registered (default)
[ 0.260304] s3c-fb exynos4-fb.0: start latency exceeded, new value 584 ns
[ 0.260342] s3c-fb exynos4-fb.0: state restore latency exceeded, new value 29125 ns
[ 0.287323] Console: switching to colour frame buffer device 100x30
[ 0.290500] s3c-fb exynos4-fb.0: window 0: fb
[ 0.293671] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
[ 0.293680] dma-pl330 dma-pl330.0: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.296582] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
[ 0.296590] dma-pl330 dma-pl330.1: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.297480] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-267056
[ 0.297489] dma-pl330 dma-pl330.2: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 0.349592] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.350487] exynos4210-uart.0: ttySAC0 at MMIO 0x13800000 (irq = 84) is a S3C6400/10
[ 1.200824] console [ttySAC0] enabled
[ 1.204687] exynos4210-uart.1: ttySAC1 at MMIO 0x13810000 (irq = 85) is a S3C6400/10
[ 1.212387] exynos4210-uart.2: ttySAC2 at MMIO 0x13820000 (irq = 86) is a S3C6400/10
[ 1.220111] exynos4210-uart.3: ttySAC3 at MMIO 0x13830000 (irq = 87) is a S3C6400/10
[ 1.228071] [drm] Initialized drm 1.1.0 20060810
[ 1.232352] i2c i2c-7: attached s5p_ddc into i2c adapter successfully
[ 1.238752] i2c i2c-8: attached s5p_hdmiphy into i2c adapter successfully
[ 1.245736] exynos-mixer s5p-mixer: probe start
[ 1.250356] s5p-g2d s5p-g2d.0: The exynos g2d(ver 4.1) successfully probed
[ 1.257464] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.263407] [drm] No driver support for vblank timestamp query.
[ 1.269869] exynos-drm exynos-drm: No connectors reported connected with modes
[ 1.276516] [drm] Cannot find any crtc or sizes - going 1024x768
[ 1.292212] exynos-drm exynos-drm: fb1: frame buffer device
[ 1.292275] exynos-drm exynos-drm: registered panic notifier
[ 1.293795] [drm] Initialized exynos 1.0.0 20110530 on minor 0
[ 1.299611] Mali<2>: Inserting Mali v19 device driver.
[ 1.304825] Mali<2>: Compiled: May 22 2014, time: 16:58:24.
[ 1.310365] Mali<2>: Driver revision:
[ 1.314095] Mali<2>: mali_module_init() registering driver
[ 1.319594] Mali<2>: mali_probe(): Called for platform device mali-utgard
[ 1.326337] Mali<2>: Memory system initializing
[ 1.330839] Mali<2>: Using device defined memory settings (dedicated: 0x00000000@0x00000000, shared: 0x10000000)
[ 1.341003] Mali<2>: Mali OS memory allocator created with max allocation size of 0x10000000 bytes, cpu_usage_adjust 0x00000000
[ 1.352459] Mali<2>: Using device defined frame buffer settings (0x00000000@0x00000000)
[ 1.360455] mali-utgard mali-utgard.0: start latency exceeded, new value 500 ns
[ 1.367742] mali-utgard mali-utgard.0: state restore latency exceeded, new value 3167 ns
[ 1.375813] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[ 1.381537] Mali<2>: Mali PP: Base address of PP core: 0x13008000
[ 1.387642] Mali<2>: Found Mali GPU Mali-400 MP r1p1
[ 1.393521] Mali<2>: Mali L2 cache: Creating Mali L2 cache: Mali_L2
[ 1.398824] Mali<2>: Mali MMU: Creating Mali MMU: Mali_GP_MMU
[ 1.404556] Mali<2>: Mali GP: Creating Mali GP core: Mali_GP
[ 1.410209] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP0_MMU
[ 1.416021] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[ 1.421717] Mali<2>: Mali PP: Base address of PP core: 0x13008000
[ 1.427815] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP1_MMU
[ 1.433631] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP1
[ 1.439346] Mali<2>: Mali PP: Base address of PP core: 0x1300a000
[ 1.445443] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP2_MMU
[ 1.451252] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP2
[ 1.456958] Mali<2>: Mali PP: Base address of PP core: 0x1300c000
[ 1.463063] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP3_MMU
[ 1.468872] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP3
[ 1.474587] Mali<2>: Mali PP: Base address of PP core: 0x1300e000
[ 1.480682] Mali<2>: 4+0 PP cores initialized
[ 1.485006] Mali<2>: Mali GPU Utilization: No utilization handler installed
[ 1.491968] Mali<2>: = clk_set_rate : 533 , 1000000
[ 1.497273] Mali<2>: = clk_get_rate: 533
[ 1.500879] Mali: init_mali_clock mali_clock c09cfaa8
[ 1.506022] Mali: MALI Error : failed to get vdd_g3d
[ 1.511291] Mali<2>: mali_probe(): Successfully initialized driver for platform device mali-utgard
[ 1.519904] mali-utgard mali-utgard.0: stop latency exceeded, new value 459 ns
[ 1.527109] mali-utgard mali-utgard.0: state save latency exceeded, new value 2583 ns
[ 1.535218] Mali: Mali device driver loaded
[ 1.539255] UMP: UMP device driver loaded
[ 1.548310] brd: module loaded
[ 1.551094] loop: module loaded
[ 1.551222] usbcore: registered new interface driver rndis_wlan
[ 1.555303] usbcore: registered new interface driver cdc_ether
[ 1.561111] usbcore: registered new interface driver dm9620
[ 1.566665] usbcore: registered new interface driver rndis_host
[ 1.572578] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.579186] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 1.584232] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.591537] s5p-ehci s5p-ehci: irq 102, io mem 0x12580000
[ 1.602966] s5p-ehci s5p-ehci: USB 2.0 started, EHCI 1.00
[ 1.603064] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.608788] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.615987] usb usb1: Product: S5P EHCI Host Controller
[ 1.621194] usb usb1: Manufacturer: Linux 3.8.13.16 ehci_hcd
[ 1.626835] usb usb1: SerialNumber: s5p-ehci
[ 1.631434] hub 1-0:1.0: USB hub found
[ 1.634835] hub 1-0:1.0: 3 ports detected
[ 1.639090] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.645030] exynos-ohci exynos-ohci: Already power on PHY
[ 1.650363] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
[ 1.656358] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 2
[ 1.663917] exynos-ohci exynos-ohci: irq 102, io mem 0x12590000
[ 1.726989] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.727062] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.727137] usb usb2: Product: EXYNOS OHCI Host Controller
[ 1.727196] usb usb2: Manufacturer: Linux 3.8.13.16 ohci_hcd
[ 1.729782] usb usb2: SerialNumber: exynos-ohci
[ 1.734614] hub 2-0:1.0: USB hub found
[ 1.738061] hub 2-0:1.0: 3 ports detected
[ 1.742353] usbcore: registered new interface driver cdc_acm
[ 1.747663] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.755700] s3c-hsotg s3c-hsotg: regs f0080000, irq 103
[ 1.760862] s3c-hsotg s3c-hsotg: Already power on PHY
[ 1.765900] s3c-hsotg s3c-hsotg: EPs:15
[ 1.769709] s3c-hsotg s3c-hsotg: dedicated fifos
[ 1.774321] s3c-hsotg s3c-hsotg: still being used
[ 1.779414] gadget: Gadget Serial v2.4
[ 1.782809] gadget: g_serial ready
[ 1.786291] s3c-hsotg s3c-hsotg: bound driver g_serial
[ 1.791411] s3c-hsotg s3c-hsotg: Already power on PHY
[ 1.799457] s3c-hsotg s3c-hsotg: s3c_hsotg_irq: USBRst
[ 1.801796] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.807228] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 1.813701] s5p-fimc exynos4-fimc.0: sclk_fimc rate is 160000000
[ 1.819119] s5p-fimc exynos4-fimc.0: start latency exceeded, new value 541 ns
[ 1.826233] s5p-fimc exynos4-fimc.0: state restore latency exceeded, new value 14959 ns
[ 1.834214] s5p-fimc exynos4-fimc.0: stop latency exceeded, new value 417 ns
[ 1.841243] s5p-fimc exynos4-fimc.0: state save latency exceeded, new value 2541 ns
[ 1.843007] s5p-fimc exynos4-fimc.1: sclk_fimc rate is 160000000
[ 1.854873] s5p-fimc exynos4-fimc.1: start latency exceeded, new value 416 ns
[ 1.861994] s5p-fimc exynos4-fimc.1: state restore latency exceeded, new value 14500 ns
[ 1.869974] s5p-fimc exynos4-fimc.1: stop latency exceeded, new value 417 ns
[ 1.877001] s5p-fimc exynos4-fimc.1: state save latency exceeded, new value 2000 ns
[ 1.878009] s5p-fimc exynos4-fimc.2: sclk_fimc rate is 160000000
[ 1.890631] s5p-fimc exynos4-fimc.2: start latency exceeded, new value 375 ns
[ 1.897755] s5p-fimc exynos4-fimc.2: state restore latency exceeded, new value 14125 ns
[ 1.905737] s5p-fimc exynos4-fimc.2: stop latency exceeded, new value 375 ns
[ 1.912765] s5p-fimc exynos4-fimc.2: state save latency exceeded, new value 1958 ns
[ 1.912937] s5p-fimc exynos4-fimc.3: sclk_fimc rate is 160000000
[ 1.926392] s5p-fimc exynos4-fimc.3: start latency exceeded, new value 416 ns
[ 1.933518] s5p-fimc exynos4-fimc.3: state restore latency exceeded, new value 14125 ns
[ 1.941499] s5p-fimc exynos4-fimc.3: stop latency exceeded, new value 417 ns
[ 1.948526] s5p-fimc exynos4-fimc.3: state save latency exceeded, new value 2000 ns
[ 1.953336] s5p-fimc-md: Registered fimc.0.m2m as /dev/video10
[ 1.953462] s5p-fimc-md: Registered fimc.0.capture as /dev/video11
[ 1.953579] s5p-fimc-md: Registered fimc.1.m2m as /dev/video12
[ 1.953704] s5p-fimc-md: Registered fimc.1.capture as /dev/video13
[ 1.953819] s5p-fimc-md: Registered fimc.2.m2m as /dev/video14
[ 1.953934] s5p-fimc-md: Registered fimc.2.capture as /dev/video15
[ 1.954069] s5p-fimc-md: Registered fimc.3.m2m as /dev/video16
[ 1.954185] s5p-fimc-md: Registered fimc.3.capture as /dev/video17
[ 1.954788] sclk_mfc rate is: 200
[ 1.954942] s5p-mfc s5p-mfc: decoder registered as /dev/video8
[ 1.955062] s5p-mfc s5p-mfc: encoder registered as /dev/video9
[ 1.955462] Exynos: Kernel Thermal management registered
[ 1.955627] cpuidle: using governor ladder
[ 1.955693] sdhci: Secure Digital Host Controller Interface driver
[ 1.955694] sdhci: Copyright(c) Pierre Ossman
[ 1.955761] s3c-sdhci exynos4-sdhci.2: clock source 2: mmc_busclk.2 (400000000 Hz)
[ 1.955796] mmc0: no vqmmc regulator found
[ 1.955799] mmc0: no vmmc regulator found
[ 2.054517] s5p-fimc exynos4-fimc.3: stop latency exceeded, new value 625 ns
[ 2.054525] usb 1-2: new high-speed USB device number 2 using s5p-ehci
[ 2.073065] mmc0: SDHCI controller on samsung-hsmmc [exynos4-sdhci.2] using ADMA
[ 2.075470] s3c-sdhci exynos4-sdhci.3: clock source 2: mmc_busclk.2 (400000000 Hz)
[ 2.083000] mmc1: no vqmmc regulator found
[ 2.087040] mmc1: no vmmc regulator found
[ 2.115240] mmc0: new high speed SDHC card at address e624
[ 2.115556] mmcblk0: mmc0:e624 SU08G 7.40 GiB
[ 2.116741] mmcblk0: p1 p2
[ 2.117974] mmc1: SDHCI controller on samsung-hsmmc [exynos4-sdhci.3] using ADMA
[ 2.119273] dw_mmc dw_mmc: Using internal DMA controller.
[ 2.119359] mmc2: no vmmc regulator found
[ 2.147976] DWMMC: Div 2 = 130
[ 2.148010] dw_mmc dw_mmc: Version ID is 240a
[ 2.148015] dw_mmc dw_mmc: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo
[ 2.148145] mmc_host mmc2: Bus speed (slot 0) = 104000000Hz (slot req 400000Hz, actual 400000HZ div = 130)
[ 2.151782] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.157599] usbcore: registered new interface driver usbhid
[ 2.162835] usbhid: USB HID core driver
[ 2.166735] cec: Probe start
[ 2.169519] s5p_cec_probe: pdata=e70b3940
[ 2.173523] s5p_cec_mem_probe(): mapped cec_base to f00aa000, size 0x1000
[ 2.180406] cec: Requesting irq 146 for s5p-cec
[ 2.184819] cec: probe successful
[ 2.189190] TCP: cubic registered
[ 2.191012] mmc2: BKOPS_EN bit is not set
[ 2.192253] DWMMC: Div 2 = 1
[ 2.192260] mmc_host mmc2: Bus speed (slot 0) = 104000000Hz (slot req 52000000Hz, actual 52000000HZ div = 1)
[ 2.192427] mmc2: new high speed DDR MMC card at address 0001
[ 2.192684] mmcblk1: mmc2:0001 M4G1YC 3.64 GiB
[ 2.192759] mmcblk1boot0: mmc2:0001 M4G1YC partition 1 2.00 MiB
[ 2.192818] mmcblk1boot1: mmc2:0001 M4G1YC partition 2 2.00 MiB
[ 2.192870] mmcblk1rpmb: mmc2:0001 M4G1YC partition 3 128 KiB
[ 2.193649] mmcblk1: p1
[ 2.195105] mmcblk1boot1: unknown partition table
[ 2.195933] mmcblk1boot0: unknown partition table
[ 2.198407] usb 1-2: New USB device found, idVendor=0424, idProduct=2640
[ 2.198411] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.198906] hub 1-2:1.0: USB hub found
[ 2.199029] hub 1-2:1.0: 3 ports detected
[ 2.269438] NET: Registered protocol family 17
[ 2.273889] NET: Registered protocol family 15
[ 2.278296] NET: Registered protocol family 35
[ 2.282932] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 2.290382] ThumbEE CPU extension supported.
[ 2.294642] Registering SWP/SWPB emulation handler
[ 2.299962] DRM: mali_platform_drm_probe()
[ 2.303470] mali_drm_init(), driver name: mali_drm, version 0.1
[ 2.309581] DRM: mali_driver_load()
[ 2.312835] [drm] Initialized mali_drm 0.1.0 20100520 on minor 1
[ 2.318965] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-01 00:51:55 UTC (946687915)
[ 2.327271] exynos_cpufreq_init: failed to get resource vdd_arm
[ 2.333179] ALSA device list:
[ 2.336077] No soundcards found.
[ 2.339508] Warning: unable to open an initial console.
[ 2.346522] Freeing init memory: 3812K
[ 2.393329] systemd-udevd[1343]: starting version 204
[ 2.483162] usb 1-2.1: new high-speed USB device number 3 using s5p-ehci
[ 2.594413] usb 1-2.1: New USB device found, idVendor=0424, idProduct=4040
[ 2.594496] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.594574] usb 1-2.1: Product: Ultra Fast Media Reader
[ 2.594630] usb 1-2.1: Manufacturer: Generic
[ 2.595725] usb 1-2.1: SerialNumber: 000000264001
[ 2.638302] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 2.638384] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 2.683168] usb 1-2.2: new full-speed USB device number 4 using s5p-ehci
[ 2.788277] usb 1-2.2: not running at top speed; connect to a high speed hub
[ 2.863027] usb 1-2.2: New USB device found, idVendor=0a46, idProduct=9621
[ 2.863102] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.865527] dm962x: dm_read_reg() 0x29 0x0a
[ 2.865773] dm962x: dm_read_reg() 0x28 0x46
[ 2.866024] dm962x: dm_read_reg() 0x2b 0x96
[ 2.867522] dm962x: dm_read_reg() 0x2a 0x21
[ 2.871898] dm962x: dm_read_reg() 0xF2 0x00
[ 2.876044] dm962x: [Analysis.2] 0xF2, D[7] 0 OK
[ 2.880408] dm962x: [Analysis.2] 0xF2, D[6] 0 OK
[ 2.886362] dm962x: [Analysis.2] 0xF2, D[5] 0 EP1: Empty
[ 2.890598] dm962x: [Analysis.2] 0xF2, D[3] 0 OK
[ 2.895166] dm962x: [Analysis.2] 0xF2, D[2] 0 OK
[ 2.901431] dm962x: [Analysis.2] 0xF2, D[1] 0 OK
[ 2.904537] dm962x: [Analysis.2] 0xF2, D[0] 0 Status: TX buffer 0 pkts
[ 2.919023] dm962x: ethernet MAC address 00:00:ff:ff:00:00 (chip)
[ 2.919521] dm962x: 9620 Mode = 128
[ 2.936041] dm9620 1-2.2:1.0 eth0: register 'dm9620' at usb-s5p-ehci-2.2, Davicom DM9620 USB Ethernet, 00:00:ff:ff:00:00
