主题 : 使用了huhu的6410的Openwrt的zImage,,,启动不来根文件系统,,,求解 复制链接 | 浏览器收藏 | 打印
学习Openwrt的。。。
级别: 侠客
UID: 107017
精华: 0
发帖: 64
金钱: 320 两
威望: 64 点
贡献值: 0 点
综合积分: 128 分
注册时间: 2014-08-11
最后登录: 2015-07-10
楼主  发表于: 2015-01-14 10:40

 使用了huhu的6410的Openwrt的zImage,,,启动不来根文件系统,,,求解

U-Boot 1.1.6 (Oct 18 2011 - 15:23:51) for FriendlyARM MINI6410


CPU:     S3C6410@532MHz
         Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board:   MINI6410
DRAM:    256 MB
Flash:   0 kB
NAND:    256 MB
In:      serial
Out:     serial
Err:     serial
MAC: 08:90:90:90:90:90
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x80000, size 0x500000
........................................ 5242880 bytes read: OK
Boot with zImage

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.36.4 (hu@hu-netbook) (gcc version 4.4.3 (GCC) ) #1 PREEMPT Fri Jan 27 08:51:40 CST 2012
[    0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Mini6410
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU S3C6410 (id 0x36410101)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] camera: no parent clock specified
[    0.000000] S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
[    0.000000] S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
[    0.000000] mout_apll: source is fout_apll (1), rate is 532000000
[    0.000000] mout_epll: source is epll (1), rate is 24000000
[    0.000000] mout_mpll: source is mpll (1), rate is 532000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] usb-bus-host: source is clk_48m (0), rate is 48000000
[    0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[    0.000000] camera: no parent clock specified
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,ext2 init=/linuxrc console=ttySAC0,115200 lcd=S70
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 255268k/255268k available, 6876k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xff600000 - 0xffe00000   (   8 MB)
[    0.000000]     vmalloc : 0xd0800000 - 0xe0000000   ( 248 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0029000   ( 132 kB)
[    0.000000]       .text : 0xc0029000 - 0xc041e000   (4052 kB)
[    0.000000]       .data : 0xc041e000 - 0xc0444220   ( 153 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000]  Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:246
[    0.000000] VIC @f4000000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f4010000: id 0x00041192, vendor 0x41
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC0] enabled
[    0.030000] Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208)
[    0.280000] pid_max: default: 32768 minimum: 301
[    0.280000] Mount-cache hash table entries: 512
[    0.280000] CPU: Testing write buffer coherency: ok
[    0.290000] NET: Registered protocol family 16
[    0.320000] LEDs initialized.
[    0.320000] s3c64xx_dma_init: Registering DMA channels
[    0.320000] s3c64xx_dma_init1: registering DMA 0 (d0808100)
[    0.330000] s3c64xx_dma_init1: registering DMA 1 (d0808120)
[    0.330000] s3c64xx_dma_init1: registering DMA 2 (d0808140)
[    0.340000] s3c64xx_dma_init1: registering DMA 3 (d0808160)
[    0.340000] s3c64xx_dma_init1: registering DMA 4 (d0808180)
[    0.350000] s3c64xx_dma_init1: registering DMA 5 (d08081a0)
[    0.350000] s3c64xx_dma_init1: registering DMA 6 (d08081c0)
[    0.360000] s3c64xx_dma_init1: registering DMA 7 (d08081e0)
[    0.360000] PL080: IRQ 73, at d0808000
[    0.370000] s3c64xx_dma_init1: registering DMA 8 (d080c100)
[    0.370000] s3c64xx_dma_init1: registering DMA 9 (d080c120)
[    0.380000] s3c64xx_dma_init1: registering DMA 10 (d080c140)
[    0.380000] s3c64xx_dma_init1: registering DMA 11 (d080c160)
[    0.390000] s3c64xx_dma_init1: registering DMA 12 (d080c180)
[    0.400000] s3c64xx_dma_init1: registering DMA 13 (d080c1a0)
[    0.400000] s3c64xx_dma_init1: registering DMA 14 (d080c1c0)
[    0.410000] s3c64xx_dma_init1: registering DMA 15 (d080c1e0)
[    0.410000] PL080: IRQ 74, at d080c000
[    0.420000] S3C6410: Initialising architecture
[    0.470000] bio: create slab <bio-0> at 0
[    0.470000] SCSI subsystem initialized
[    0.470000] usbcore: registered new interface driver usbfs
[    0.480000] usbcore: registered new interface driver hub
[    0.480000] usbcore: registered new device driver usb
[    0.490000] s3c-i2c s3c2440-i2c: slave address 0x10
[    0.490000] s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
[    0.500000] s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
[    0.500000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[    0.560000] NET: Registered protocol family 2
[    0.560000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.570000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.570000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.580000] TCP: Hash tables configured (established 8192 bind 8192)
[    0.590000] TCP reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] NET: Registered protocol family 1
[    0.610000] audit: initializing netlink socket (disabled)
[    0.610000] type=2000 audit(0.610:1): initialized
[    0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.650000] Registering mini_fo version $Id$
[    0.660000] JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (RUBIN) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.670000] msgmni has been set to 498
[    0.670000] io scheduler noop registered (default)
[    0.680000] S3C_LCD clock got enabled :: 133.000 Mhz
[    0.700000] LCD TYPE :: N43 will be initialized
[    0.700000] Window[0] - FB1: map_video_memory: clear ff600000:0013ec00
[    0.710000]             FB1: map_video_memory: dma=5fa00000 cpu=ff600000 size=0013ec00
[    0.710000] Console: switching to colour frame buffer device 60x17
[    0.720000] fb0: s3cfb frame buffer device
[    0.720000] backlight        initialized
[    1.400000] gpiodev: gpio device registered with major 253
[    1.400000] leds     initialized
[    1.400000] adc      initialized
[    1.400000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.410000] s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
[    1.420000] s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
[    1.430000] s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
[    1.430000] s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
[    1.450000] S3C NAND Driver, (c) 2008 Samsung Electronics
[    1.450000] S3C NAND Driver ECC Disabled.
[    1.450000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
[    1.460000] NAND_ECC_NONE selected by board driver. This is not recommended !!
[    1.470000] Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
[    1.470000] 0x000000000000-0x000000080000 : "Bootloader"
[    1.480000] 0x000000080000-0x000000580000 : "Kernel"
[    1.490000] 0x000000580000-0x000010000000 : "rootfs"
[    1.560000] mtd: partition "rootfs" set to be root filesystem
[    1.560000] split_squashfs: no squashfs found in "NAND 256MiB 3,3V 8-bit"
[    1.570000] dm9000 Ethernet Driver, V1.31
[    1.690000] eth0: dm9000a at d08da000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90 (chip)
[    1.690000] mice: PS/2 mouse device common for all mice
[    1.700000] touchscreen-1wire        initialized
[    1.700000] backlight-1wire  initialized
[    1.700000] input: TouchScreen Pipe as /devices/virtual/input/input0
[    1.710000] ts-if    initialized
[    1.710000] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    1.720000] one_wire_status: 4
[    1.720000] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    1.730000] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    1.730000] i2c /dev entries driver
[    1.740000] Linux video capture interface: v2.00
[    1.740000] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[    1.750000] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[    1.750000] cpuidle: using governor ladder
[    1.760000] one_wire_status: 4
[    1.760000] sdhci: Secure Digital Host Controller Interface driver
[    1.770000] sdhci: Copyright(c) Pierre Ossman
[    1.770000] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
[    1.780000] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
[    1.780000] s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
[    1.790000] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[    1.800000] one_wire_status: 2
[    1.810000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
[    1.810000] specify port
[    1.810000] snd_mpu401: probe of snd_mpu401.0 failed with error -22
[    1.820000] usbcore: registered new interface driver snd-usb-audio
[    1.820000] asoc: AC97 HiFi <-> s3c-ac97 mapping ok
[    1.950000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004100, 3=00008080
[    1.950000] mmc0: new high speed SDHC card at address aaaa
[    1.950000] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
[    1.970000]  mmcblk0: p1
[    2.950000] AC97: Unable to activate!
[    3.990000] AC97: Unable to activate!
[    4.990000] AC97: Unable to read!
[    6.070000] AC97: Unable to activate!
[    7.110000] AC97: Unable to activate!
[    8.110000] AC97: Unable to read!
[    9.230000] AC97: Unable to activate!
[   10.270000] AC97: Unable to activate!
[   11.270000] AC97: Unable to read!
[   11.270000] Failed to reset WM9713: AC97 link error
[   11.270000] ALSA device list:
[   11.270000]   No soundcards found.
[   11.270000] TCP westwood registered
[   11.280000] NET: Registered protocol family 17
[   11.280000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[   11.290000] All bugs added by David S. Miller <davem@redhat.com>
[   11.300000] one_wire_status: 2
[   11.310000] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-22 14:46:40 UTC (948552400)
[   11.310000] VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
[   11.320000] Please append a correct "root=" boot option; here are the available partitions:
[   11.320000] 1f00             512 mtdblock0 (driver?)
[   11.330000] 1f01            5120 mtdblock1 (driver?)
[   11.330000] 1f02          256512 mtdblock2one_wire_status: 2
[   11.340000]  (driver?)
[   11.340000] b300         7761920 mmcblk0 driver: mmcblk
[   11.350000]   b301         7628800 mmcblk0p1
[   11.350000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
[   11.360000] one_wire_status: 2
[   11.360000] Backtrace:
[   11.360000] [<c002d5a4>] (dump_backtrace+0x0/0x10c) from [<c033e110>] (dump_stack+0x18/0x1c)
[   11.370000]  r7:00008000one_wire_status: 4
[   11.380000]  r6:c0023a14 r5:c0444f10 r4:c0444f10
[   11.380000] [<c033e0f8>] (dump_stack+0x0/0x1c) from [<c033e190>] (panic+0x7c/0x19c)
[   11.390000] [<c033e114>] (panic+0x0/0x19c) from [<c0008e38>] (mount_block_root+0x1f8/0x2bc)
[   11.400000] one_wire_status: 4
[   11.400000]  r3:00000000 r2:00000000 r1:cf829f60 r0:c03bdf98
[   11.410000] [<c0008c40>] (mount_block_root+0x0/0x2bc) from [<c0008f50>] (mount_root+0x54/0x6c)
[   11.420000] one_wire_status: 4
[   11.420000] [<c0008efc>] (mount_root+0x0/0x6c) from [<c000909c>] (prepare_namespace+0x134/0x18c)
[   11.430000]  r5:c0023a29 r4:c0444304
[   11.430000] [<c0008f68>] (prepare_namespace+0x0/0x18c) from [<c00084e8>] (kernel_init+0x114/0x154)
[   11.440000] one_wire_status: 4
[   11.440000]  r5:c0022da4 r4:c04442a0
[   11.450000] [<c00083d4>] (kernel_init+0x0/0x154) from [<c00406dc>] (do_exit+0x0/0x694)
[   11.450000]  r5:c00083d4one_wire_status: 4
[   11.460000]  r4:00000000
学习Openwrt的。。。
级别: 侠客
UID: 107017
精华: 0
发帖: 64
金钱: 320 两
威望: 64 点
贡献值: 0 点
综合积分: 128 分
注册时间: 2014-08-11
最后登录: 2015-07-10
1楼  发表于: 2015-01-14 10:40