主题 : mini6410挂载文件系统失败。。。 复制链接 | 浏览器收藏 | 打印
学习Openwrt的。。。
级别: 侠客
UID: 107017
精华: 0
发帖: 64
金钱: 320 两
威望: 64 点
贡献值: 0 点
综合积分: 128 分
注册时间: 2014-08-11
最后登录: 2015-07-10
楼主  发表于: 2015-01-15 15:38

 mini6410挂载文件系统失败。。。

NAND read: device 0 offset 0x80000, size 0x500000
........................................Boot with zImage

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.36.4 (lintel@lintel-Aspire-4741) (gcc version 4.3.3 (GCC) ) #6 PREEMPT Sat Aug1
[    0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Mini6410
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU S3C6410 (id 0x36410101)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] camera: no parent clock specified
[    0.000000] S3C64XX: PLL settings, A=666000000, M=532000000, E=24000000
[    0.000000] S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
[    0.000000] mout_apll: source is fout_apll (1), rate is 666000000
[    0.000000] mout_epll: source is epll (1), rate is 24000000
[    0.000000] mout_mpll: source is mpll (1), rate is 532000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] usb-bus-host: source is clk_48m (0), rate is 48000000
[    0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[    0.000000] camera: no parent clock specified
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttySAC0,115200
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 255260k/255260k available, 6884k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xff600000 - 0xffe00000   (   8 MB)
[    0.000000]     vmalloc : 0xd0800000 - 0xe0000000   ( 248 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc002a000   ( 136 kB)
[    0.000000]       .text : 0xc002a000 - 0xc0420000   (4056 kB)
[    0.000000]       .data : 0xc0420000 - 0xc0446640   ( 154 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000]  Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:246
[    0.000000] VIC @f4000000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f4010000: id 0x00041192, vendor 0x41
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC0] enabled
[    0.020000] Calibrating delay loop... 665.19 BogoMIPS (lpj=3325952)
[    0.260000] pid_max: default: 32768 minimum: 301
[    0.260000] Mount-cache hash table entries: 512
[    0.260000] CPU: Testing write buffer coherency: ok
[    0.270000] NET: Registered protocol family 16
[    0.300000] LEDs initialized.
[    0.300000] s3c64xx_dma_init: Registering DMA channels
[    0.300000] s3c64xx_dma_init1: registering DMA 0 (d0808100)
[    0.310000] s3c64xx_dma_init1: registering DMA 1 (d0808120)
[    0.310000] s3c64xx_dma_init1: registering DMA 2 (d0808140)
[    0.320000] s3c64xx_dma_init1: registering DMA 3 (d0808160)
[    0.320000] s3c64xx_dma_init1: registering DMA 4 (d0808180)
[    0.330000] s3c64xx_dma_init1: registering DMA 5 (d08081a0)
[    0.340000] s3c64xx_dma_init1: registering DMA 6 (d08081c0)
[    0.340000] s3c64xx_dma_init1: registering DMA 7 (d08081e0)
[    0.350000] PL080: IRQ 73, at d0808000
[    0.350000] s3c64xx_dma_init1: registering DMA 8 (d080c100)
[    0.360000] s3c64xx_dma_init1: registering DMA 9 (d080c120)
[    0.360000] s3c64xx_dma_init1: registering DMA 10 (d080c140)
[    0.370000] s3c64xx_dma_init1: registering DMA 11 (d080c160)
[    0.370000] s3c64xx_dma_init1: registering DMA 12 (d080c180)
[    0.380000] s3c64xx_dma_init1: registering DMA 13 (d080c1a0)
[    0.380000] s3c64xx_dma_init1: registering DMA 14 (d080c1c0)
[    0.390000] s3c64xx_dma_init1: registering DMA 15 (d080c1e0)
[    0.400000] PL080: IRQ 74, at d080c000
[    0.400000] S3C6410: Initialising architecture
[    0.450000] bio: create slab <bio-0> at 0
[    0.460000] SCSI subsystem initialized
[    0.460000] usbcore: registered new interface driver usbfs
[    0.460000] usbcore: registered new interface driver hub
[    0.470000] usbcore: registered new device driver usb
[    0.470000] s3c-i2c s3c2440-i2c: slave address 0x10
[    0.480000] s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
[    0.480000] s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
[    0.490000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[    0.550000] NET: Registered protocol family 2
[    0.550000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.560000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.560000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.570000] TCP: Hash tables configured (established 8192 bind 8192)
[    0.580000] TCP reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.600000] audit: initializing netlink socket (disabled)
[    0.600000] type=2000 audit(0.600:1): initialized
[    0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.640000] Registering mini_fo version $Id$
[    0.650000] JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (RUBIN) (CMODE_PRIORITY) (c) 2001.
[    0.660000] msgmni has been set to 498
[    0.660000] io scheduler noop registered (default)
[    0.670000] S3C_LCD clock got enabled :: 133.000 Mhz
[    0.690000] LCD TYPE :: A70 will be initialized
[    0.700000] Window[0] - FB1: map_video_memory: clear ff600000:003a9800
[    0.720000]             FB1: map_video_memory: dma=5f000000 cpu=ff600000 size=003a9800
[    0.730000] Console: switching to colour frame buffer device 100x30
[    0.750000] fb0: s3cfb frame buffer device
[    0.750000] backlight        initialized
[    1.500000] gpiodev: gpio device registered with major 253
[    1.500000] adc      initialized
[    1.510000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.520000] s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
[    1.520000] s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
[    1.530000] s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
[    1.540000] s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
[    1.550000] S3C NAND Driver, (c) 2008 Samsung Electronics
[    1.550000] S3C NAND Driver ECC Disabled.
[    1.550000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
[    1.560000] NAND_ECC_NONE selected by board driver. This is not recommended !!
[    1.570000] Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
[    1.580000] 0x000000000000-0x000000080000 : "Bootloader"
[    1.590000] 0x000000080000-0x000000580000 : "Kernel"
[    1.590000] 0x000000580000-0x000010000000 : "rootfs"
[    1.660000] mtd: partition "rootfs" set to be root filesystem
[    1.670000] split_squashfs: no squashfs found in "NAND 256MiB 3,3V 8-bit"
[    1.680000] dm9000 Ethernet Driver, V1.31
[    1.800000] eth0: dm9000a at d08da000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90 (chip)
[    1.800000] mice: PS/2 mouse device common for all mice
[    1.810000] touchscreen-1wire        initialized
[    1.810000] backlight-1wire  initialized
[    1.810000] input: TouchScreen Pipe as /devices/virtual/input/input0
[    1.820000] ts-if    initialized
[    1.820000] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    1.830000] one_wire_status: 5
[    1.830000] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    1.840000] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    1.840000] i2c /dev entries driver
[    1.850000] Linux video capture interface: v2.00
[    1.850000] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[    1.860000] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[    1.860000] cpuidle: using governor ladder
[    1.870000] one_wire_status: 4
[    1.870000] sdhci: Secure Digital Host Controller Interface driver
[    1.880000] sdhci: Copyright(c) Pierre Ossman
[    1.880000] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
[    1.890000] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
[    1.890000] s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
[    1.900000] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[    1.910000] one_wire_status: 4
[    1.910000] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
[    1.920000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
[    1.920000] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
[    1.930000] one_wire_status: 4
[    1.930000] s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
[    1.940000] enter s3c64xx_setup_sdhci1_cfg_gpio
[    1.950000] one_wire_status: 4
[    1.950000] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[    1.960000] specify port
[    1.960000] snd_mpu401: probe of snd_mpu401.0 failed with error -22
[    1.970000] usbcore: registered new interface driver snd-usb-audio
[    1.970000] asoc: AC97 HiFi <-> s3c-ac97 mapping ok
[    2.080000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004100, 3=00008080
[    2.080000] mmc0: new high speed SDHC card at address aaaa
[    2.080000] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
[    2.100000]  mmcblk0: p1
[    2.120000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
[    3.100000] AC97: Unable to activate!
[    4.140000] AC97: Unable to activate!
[    5.140000] AC97: Unable to read!
[    6.220000] AC97: Unable to activate!
[    7.260000] AC97: Unable to activate!
[    8.260000] AC97: Unable to read!
[    9.380000] AC97: Unable to activate!
[   10.420000] AC97: Unable to activate!
[   11.420000] AC97: Unable to read!
[   11.420000] Failed to reset WM9713: AC97 link error
[   11.420000] ALSA device list:
[   11.420000]   No soundcards found.
[   11.420000] TCP westwood registered
[   11.430000] NET: Registered protocol family 17
[   11.430000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[   11.440000] All bugs added by David S. Miller <davem@redhat.com>
[   11.450000] one_wire_status: 2
[   11.460000] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-23 19:43:50 UTC (948656630)
[   11.460000] List of all partitions:
[   11.460000] 1f00             512 mtdblock0 (driver?)
[   11.470000] 1f01            5120 mtdblock1 (driver?)
[   11.470000] 1f02          256512 mtdblock2 (driver?)
[   11.480000] b300         7761920 mmcblk0 driver: mmcblk
[   11.480000]   b301         7628800 mmcblk0p1one_wire_status: 2
[   11.490000]
[   11.490000] No filesystem could mount root, tried:  squashfs
[   11.500000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
[   11.500000] Backtrace: one_wire_status: 2
[   11.510000]
[   11.510000] [<c002e528>] (dump_backtrace+0x0/0x10c) from [<c0341a10>] (dump_stack+0x18/0x1c)
[   11.520000]  r7:00008000 r6:cf812000 r5:c068289f r4:cf829f50
[   11.520000] [<c03419f8>] (dump_stack+0x0/0x1c) from [<c0341a8c>] (panic+0x78/0x194)
[   11.530000] one_wire_status: 4
[   11.530000] [<c0341a14>] (panic+0x0/0x194) from [<c0008ed4>] (mount_block_root+0x26c/0x2bc)
[   11.540000]  r3:00000029 r2:00000020one_wire_status: 4
[   11.550000]  r1:cf829f50 r0:c03c09f8
[   11.550000] [<c0008c68>] (mount_block_root+0x0/0x2bc) from [<c0008f78>] (mount_root+0x54/0x6c)
[   11.560000] [<c0008f24>] (mount_root+0x0/0x6c) from [<c00090c0>] (prepare_namespace+0x130/0x188)
[   11.570000] one_wire_status: 4
[   11.570000]  r5:c0024a14 r4:c0446724
[   11.580000] [<c0008f90>] (prepare_namespace+0x0/0x188) from [<c00084e8>] (kernel_init+0x114/0x154)
[   11.580000]  r6:c0041434one_wire_status: 4
[   11.590000]  r5:c00230b0 r4:c00230b0
[   11.590000] [<c00083d4>] (kernel_init+0x0/0x154) from [<c0041434>] (do_exit+0x0/0x6ac)
[   11.600000]  r5:c00083d4 r4:00000000
学习Openwrt的。。。
级别: 侠客
UID: 107017
精华: 0
发帖: 64
金钱: 320 两
威望: 64 点
贡献值: 0 点
综合积分: 128 分
注册时间: 2014-08-11
最后登录: 2015-07-10
1楼  发表于: 2015-01-15 15:39
       lintel的Openwrt -zImage